FREE STANDARD SHIPPING FOR ORDERS OVER $50 AND FREE RETURN SHIPPING

ProFlight Aviation Headset

Sold from 2018 – present

NOT YOUR PRODUCT?
Help us provide the best support by confirming your product below
Select your product
Product image
SUPPORT OPTIONS FOR
Loading
SEARCH
Enter a search term in the field above.
Nothing found. Please enter a valid search (e.g. connection help, no audio from headphones etc.).

Clicking sound in both earcups

If your headphones produce an unexpected ticking, clicking or popping noise from both sides of the headset, try the following:

Determine if any recent changes have been made to the headset or aircraft.

If any changes or modifications have been made to either the headset or the aircraft, look into whether or not those changes could have unexpectedly caused this issue.

Check if the noise is affected by the volume control on the aircraft panel volume control.

Without adjusting your headset volume, turn up or down the volume control on the aircraft panel. If the noise level changes as well, the noise is related to the signal being received from the panel.

Connect the headset to a different panel jack or, if possible, to another aircraft.

Non-TSO equipment, worn jacks/loose connections, or incorrectly wired jacks (i.e. reversed stereo or mic / ground wires) in the aircraft can cause issues. If available, try connecting the headset to another jack in the aircraft or to jacks in a separate aircraft. If the headset works fine when connected elsewhere, the panel jack or wiring to the jack is the issue.

For 6-pin aircraft-powered installed connections, check the condition of the plug on the headset and the jack on the aircraft.

Check for any debris in the connector on the aircraft and check if any of the six pins are missing inside the headset plug.

Note: If the aircraft has a jack for an older model Bose AHX headset that was wired to provide mono audio to the right earcup, the jack will need to be rewired since the electronics in the newer A20 cable differ.

Determine if the issue occurs when your headset is powered off.

Your headset works in passive mode (powered off with no noise cancellation). If the issue still occurs while the headset is powered off, the issue is related to signal coming being received by the headset from the aircraft panel (i.e. the connections, wiring, or interference).

Install new double-A alkaline batteries.

Remove the batteries from you product, then insert new batteries. Check that the + and  markings on the batteries match the markings in the battery compartment. (Note: Rechargeable batteries are not recommended. Use alkaline batteries when possible.)

Check for interference that could be causing unwanted noise.

While the noise is present, slowly move or turn your head away from sources of interference — like window heat, antennae, power cords, etc. If the noise is more noticeable as you get closer to a device or area in the aircraft, it is related to interference from that device or area. In some cases, repositioning even just a few inches can help. (Tip: If necessary, the headset can be used in passive mode — powered off with no noise cancellation — to avoid interference).

Determine if the tone of the noise changes when the avionics panel is touched.

If the tone changes when the avionics panel or any other area of the plane is touched, there may be a grounding issue with the aircraft or the intercom connections and associated wiring.

Determine if the issue occurs when the mic is in use.

If the issue only occurs when speaking through the microphone, the Down Cable may be defective. Follow the link for more information on how to service your product. Depending on your product and region, you will be provided a contact number or the ability to setup service online.

Click here to start service

Determine if the issue occurs at the same tempo of the LED on the Down Cable.

If the issue only occurs when the LED on the Down Cable is blinking, the Down Cable may be defective. Follow the link for more information on how to service your product. Depending on your product and region, you will be provided a contact number or the ability to setup service online.

Click here to start service

Your product may need service.

If the steps provided do not resolve your issue, your product may need service. Follow the link below for more information on how to service your product. Depending on your product and region, you will be provided a contact number or the ability to setup service online.

Click here to start service
Was this article helpful?
Submit
Thank you for your feedback!